Protest fund fundraiser ' ROLAND OUT ' Hoodie , pin and iron on badge , £10 plus p&p
Comments
-
KIDS HOODIES ARE £5 plus p&p0
-
XL hoodie please0
-
Message sent Charltonkeston0
-
Ted\'s Addicksson I have tried to message you but I get the message user not found0
-
I'm here, honest!0
-
Shall I PM my proper email address?0
-
Yes please Ted0
-
One XL and one Medium please0
-
Great work @charltonnick . Thank you.1
-
Thanks Davo55 £100 transferred to the protest fund with a few more orders in the pipeline1
-
Sponsored links:
-
May I have a small men’s plse.0
-
May I have an adult XL please? Thanks.
0 -
Yes Hoof-hearted I have messaged you0
-
Just Small , XL and 3XL now left , plenty of kids sizes which are only £50
-
Adult XL for me please0
-
XL reserved for you red10 , messaged you0
-
You lost me at "an iron"charltonnick said:Just for you IdleHans
Application instructions for your badges, its simple. You will need:
• an iron
• a firm flat surface – a table is better than an ironing board
• a damp sponge
• a thin piece of cloth
• your garment
• and an iron-on emblem.
1. Switch on your iron, set it to the maximum temperature and allow it to warm up.
2. Very lightly dampen the area where you want to apply the emblem.
3. Place the emblem with the embroidery facing you
4. Cover the emblem with the thin cloth and press as firmly as you can for 60 seconds on both sides of the garment. Do not use steam.
5. Turn the garment inside out and repeat the process
6. Check that the edges are properly bonded and allow the garment to cool
The bond reaches maximum strength after 24 hours so try to avoid the wearing the garment during that period. The garment can be washed according to the care label4 -
3xl hoodie please0
-
Idle by name, idle by nature??
0 -
I thought everyone knew that’s the name for a West Ham supporter. Some people, heh!IdleHans said:
You lost me at "an iron"charltonnick said:Just for you IdleHans
Application instructions for your badges, its simple. You will need:
• an iron
• a firm flat surface – a table is better than an ironing board
• a damp sponge
• a thin piece of cloth
• your garment
• and an iron-on emblem.
1. Switch on your iron, set it to the maximum temperature and allow it to warm up.
2. Very lightly dampen the area where you want to apply the emblem.
3. Place the emblem with the embroidery facing you
4. Cover the emblem with the thin cloth and press as firmly as you can for 60 seconds on both sides of the garment. Do not use steam.
5. Turn the garment inside out and repeat the process
6. Check that the edges are properly bonded and allow the garment to cool
The bond reaches maximum strength after 24 hours so try to avoid the wearing the garment during that period. The garment can be washed according to the care label0 -
Sponsored links:
-
Postman has just been - bringing a parcel. Thank you to all who have worked so hard to bring these goods to the market.
The hoodie fits well, with the cuffs turned back (as a shortish woman I had feared the arms would be down to my knees!) and the robin/beachball badge will be perfect for covering Roland's ugly mug when he finally f***s off, & we can all set about trying to forget this horrible period in the life of OUR club.
With the protest shirt for the summer, and the hoodie for spring and autumn, I'm now well equipped to go and help ROT campaign in Sint-Truiden! Thank you.1 -
One for me please!0
-
Chizz we only have left S , XL and 3XL left , any good for you ?0
-
Just got mine, far quicker than i expected! Decent quality hoody too, Bargain. ROLAND OUT! 10/10!
1 -
-
Have you started the Aussies Out ones yet ????1
-
Ha ha , I'm looking forward to retirement1
-
-
It will be a collectors item1
-
Mine's arrived today too with the set of badges, very quick and efficient.
Wearing it now in this freezing cold house, and it fits perfectly (XL on a 44" chest)
Quality gear at a bargain price. Get 'em while you can, addicks.
Five stars!!!
(will that do, @charltonnick ?)
0
